Baron Air & Fuel_xXx BIG AIR KIT Honda Fury BLACK User Manual download pdf

Page: 1LA-2362-00/00B

xXx BIG AIR KIT - Honda Fury

We recommend the use of a factory service manual for all installations. Our

instructions are for use as a guide only. We suggest when running the BAK

with other than stock exhaust pipes you should have your air/fuel mixture

analyzed to determine if you need a fuel injection modifier like a Dynojet,

Kuryakyn, Cobra, TFI or similar.

Revision: 2.6 - 01/13/2011

Install Time: 30 Minutes

INCLUDED IN THE KIT:

(1) Chrome or Black xXx Cover

(1) Chrome Mesh Cover

(1) Throttle Body Adapter Backplate

(1) Black Air Filter Retaining Cover

(3) 2.75" Aluminum Standoffs

(6) 1/4-20 x 3/4" Flathead Bolts

(1) 1/2" x 85mm Spacer Tube

(4) M5-.80 x 16mm Button Head Socket Screw

(1) M6-1.0 x 100mm Flathead Bolt

(1) Large O-Ring

(1) 5/16" Diameter x 3/8" Length Fuel Hose

(1) 1/4-20 x 1/2" Stainelss Flat Head

TOOLS REQUIRED:

10mm Socket & Driver & 6" Extension

4mm & 5mm Allen Wrenches

Blue Loctite®

5/32" Allen Wrench

INSTRUCTIONS:

RECOMMEND: Use Blue Loctite® on all threaded hardware.

NOTES: Before you begin, be sure to check your xXx BAK contents against the hardware list above.

1. Remove the stock air cleaner from the right side of your bike by unscrewing the (4) 5mm allen screws around

the outside edge of the chrome cover.

2. Remove the chrome cover and then remove the air filter.

3. Remove the 10mm hex head bolt located inside the bottom portion of the black air box using your extension

and 10mm socket.

4. Remove the (4) M5 phillips screws from the air box that surround the throttle body. This will allow the air

box to be removed from the bike and placed aside. You will not reinstall this part.

5. Slide the thick o-ring (supplied) over the crankcase vent return located at the 10 o'clock position on the

throttle body and be sure the o-ring is pushed back as far as it can go.

7. For the next step you will need the following items: Backing Plate, Short piece of 5/16" and Fuel hose - Take

the backing plate and insert the 5/16" fuel line into the counter-bored hole on the rear (side without the groove)

in the 6 o'clock position.

8. Put Blue Loctite® in the four threaded holes at the corners of the throttle body.

9. Take the (3) 2-1/2" aluminum spacers and put Blue Loctite® in the end that is turned down. Place them

against the front of the backing plate and insert a 1/4-20 x 3/4" Flathead bolt and tighten using a 5/32" allen

wrench until the standoffs are firmly attached.

Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or

fitment may be required. LA Choppers bears no responsibility on installation costs associated with this product.

© 2013 LA Choppers

5221 Oceanus Drive Huntington Beach, CA 92649 (925)583-2499 - Ph. (714)901-0520 - Fax www.lachoppers.com [email protected]

1 2

Summary of Contents

Page 1 - Page: 1LA-2362-00/00B

Page: 1LA-2362-00/00BxXx BIG AIR KIT - Honda FuryWe recommend the use of a factory service manual for all installations. Ourinstructions are for use a

Page 2 - Page: 2LA-2362-00/00B

Page: 2LA-2362-00/00BxXx BIG AIR KIT - Honda Fury10. Place the performance air filter into the filter groove on the backing plate. Then place Blue Loc

Comments to this Manuals

No comments