Baron Air & Fuel_NEEDLE_JET KIT Honda VTX 1300 User Manual download pdf

Page: 1BA-2461-00

BARON Jet Kit Honda VTX-1300

Revision: 1.0 - 03/15/2010

INCLUDED IN THE KIT:

(1) D Tool

(1) Slide Spring

(2) E Clips

(1) Baron Fuel Needle

(4) Baron Jets

TOOLS REQUIRED:

Factory Service Manual

Toenail Clippers

Needle Nose Pliers

8, 10, and 12mm Sockets w/ Extension

Flat Screwdriver

Phillips Screwdriver

INSTRUCTIONS:

Thank you for purchasing the Baron VTX1300 Jet Kit. Installation is reasonably simple providing you follow

the instructions below implicitly. As always, please read the instructions in full prior to installing the product. If

you feel you dont understand it, please call our tech support line, or have the product installed by a competent

technician.

1. Remove fuel tank per service manual instructions.

2. Remove the air filter and backing plate.

3. Carefully remove the vacuum slide cover from the top of the carburetor. Be careful here as the spring inside

the assembly can pop out.

4. Remove the spring and slide assembly from the carburetor. Gently pull the rubber diaphragm and the entire

assembly (slide assembly or slide") with the needle & spacers will slide right out. Do not force it.

5. Your stock needle will be sticking out of the bottom of the slide. To remove it, you must use an 8mm socket

(or Phillips screwdriver). Inside the slide you will see a yellow plastic holder. Turn this holder" 1/4 turn

counter-clockwise while pushing down on it to compress the spring and relieve pressure. The holder will pop

slightly and you will know its out. Be careful not to break this holder during this step. It only needs to turn 1/4

turn!

6. The holder, along with the needle, stock needle spring and spacers will then slide out.

7. Disassemble the needle assembly.

8. Looking inside the yellow holder, you will see the needle spring. There is a plastic nub on the inside of the

holder that locks this spring in place. Gently unscrew the spring as you pull it off this nub, trying not to distort

and overstretch the spring.

9. Use toenail clippers to clip this nub in 1/2. This will allow for greater needle adjustments without obstruction.

Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or

fitment may be required. Barons bears no responsibility on installation costs associated with this product.

5221 Oceanus Drive Huntington Beach, CA 92649 (925)583-2499 - Ph. (714)901-0520 - Fax www.baronscustom.com [email protected]

1 2 3

Summary of Contents

Page 1 - BARON Jet Kit Honda VTX-1300

Page: 1BA-2461-00BARON Jet Kit Honda VTX-1300Revision: 1.0 - 03/15/2010INCLUDED IN THE KIT:(1) D Tool(1) Slide Spring(2) E Clips(1) Baron Fuel Needle(

Page 2 - Page: 2BA-2461-00

Page: 2BA-2461-00BARON Jet Kit Honda VTX-130010. Install the Baron needle in place of the stock needle on groove #4 from the top. Use all stock spacer

Page 3 - Page: 3BA-2461-00

Page: 3BA-2461-00BARON Jet Kit Honda VTX-1300fine-tuning your motorcycle. The instructions here are only a guide. It is impossible for us to predict

Comments to this Manuals

No comments

Baron Air & Fuel_NEEDLE_JET KIT Honda VTX 1300 User Manual

Browse online or download User Manual for For motorcycles Baron Air & Fuel_NEEDLE_JET KIT Honda VTX 1300. Baron Air & Fuel_NEEDLE_JET KIT Honda VTX 1300 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For motorcycles Baron Air & Fuel_NEEDLE_JET KIT Honda VTX 1300